Differences between revisions 7 and 51 (spanning 44 versions)

The 40m has two networks: the LIGO general computing network and an internal "martian" network.

LIGO Caltech network

IP addresses on this network are in the form 131.215.114.XXX

Martian network

IP addresses on the martian network are in the form 192.168.113.XXX
The wireless network is on the martian network.

Gateway	192.168.113.2
netmask	255.255.255.0
nameserver	192.168.113.104
nameserver	131.215.125.1
nameserver	131.215.139.100
nameserver	131.215.254.99

See the Martian host table for IP address assignments on the martian network.
When you want to add a new host to the Martian network read this.
To ssh to one of the martian computers from a GC computer, ssh into controls@nodus, then use name (or name.martian) for the name. i.e.ssh pianosa.martian
Note that all the access from outside should go through nodus, while the connection from inside to outside is gatewayed by the NAT router (192.168.113.2).

Wireless Network

On Jan 6th, 2016, the Martian wifi router was replaced with a Netgear R6400. Link to the corresponding ELOG entry

The router supports a 2 GHz network (11g) named "40MARS" and a 5 GHz network (11ac) "40MARS_5G". These two SSIDs are hidden.

The martian IP address of this unit is 192.168.113.232.

Wireless Bridge for GPIB instruments

On Jan 8th, 2016, a new wireless bridge (NETGEAR EX3700) for GPIB instruments was installed.

Device Name: EX3700_1, Fixed IP: 192.168.113.233

It accepts ethernet (wired) devices with fixed IP of 192.168.113.XXX

How_To_Configure_NETGEAR_EX3700

Nameserver and DHCP

chiara runs the DNS and DHCP for the Martian network, set up largely in the manner detailed in this website.

Configuration files can be found at

chiara:/etc/bind/named.conf.local
chiara:/etc/dhcp/dhcpd.conf

and other files in those same directories.

Mount NFS filesystem

If you want to mount the /cvs/cds NFS filesystem on a computer already on the martian network, add the following line to the file /etc/fstab

chiara:/home/cds              /cvs/cds        nfs     rw,bg,nfsvers=3

Then make the directory where the /cvs/cds dir will be mounted, mount the filesystem via

mkdir -p /cvs/cds
sudo mount /cvs/cds

-  ⇤ ← Revision 7 as of 2008-09-17 17:34:00 → 
  Size: 2801
  Editor: JoeBetzwieser
  Comment:
+   ← Revision 51 as of 2018-06-01 03:02:58 → ⇥
  Size: 2599
  Editor: KojiaraiATligoDOTorg
  Comment:
-Deletions are marked like this.
+Additions are marked like this.
 Line 1:
-The 40m has two network segments: the LIGO general computing network and an internal "martian" network.
+''' The 40m has two networks: the LIGO general computing network and an internal "martian" network. '''
 Line 5:
-IP addresses on this network are in the form 131.215.'''114'''.XXX
+ . IP addresses on this network are in the form 131.215.'''114'''.XXX
 Line 9:
-IP addresses on the martian network are in the form 131.215.'''113'''.XXX
+ . IP addresses on the martian network are in the form 192.168.'''113'''.XXX
 Line 11:
-The wireless network is on the martian network.
+ . The wireless network is on the martian network.
 Line 13:
-|| Gateway    || 131.215.113.2    ||
+|| Gateway    || 192.168.113.2    ||
 Line 15:
+|| nameserver || 192.168.113.104  ||
-Line 19:
+Line 20:
-See also [[Martian Host Table]] for IP address assignments on the martian network.
+ . See the [[Martian_Host_Table|Martian host table]] for IP address assignments on the martian network.

 . When you want to add a new host to the Martian network [[CDS/How_to_join_martian | read this]].

 . To ssh to one of the martian computers from a GC computer, ssh into `controls@nodus`, then use `name` (or `name.martian`) for the name. i.e.{{{ssh pianosa.martian }}}

 . Note that all the access from outside should go through nodus, while the connection from inside to outside is gatewayed by the NAT router (192.168.113.2).
-Line 23:
+Line 30:
-The wireless network is part of the Martian Network.  The Martian ethernet is bridged to wireless via a Linksys Wireless-G access point with IP address 131.215.113.220.  Note that the wireless access point is only bridging the wired and wireless networks--it does not do NAT.   To access the outside world, your network settings should be 
the same as given above for the Martian network.  The configuration password for the wireless AP is written in a manilla folder in the usual place where equipment manuals are kept.
+On Jan 6th, 2016, the Martian wifi router was replaced with a Netgear R6400. Link to the corresponding [[https://nodus.ligo.caltech.edu:8081/40m/11916|ELOG entry]]
-Line 26:
+Line 32:
-== How to setup linux1 with a name server ==
+The router supports a 2 GHz network (11g) named "40MARS" and a 5 GHz network (11ac) "40MARS_5G". These two SSIDs are hidden.
-Line 28:
+Line 34:
-) Linux1 needs network interface statically configured.  Example on Debian:  edit /etc/network/interfaces, make an entry like
+The martian IP address of this unit is 192.168.113.232.
-Line 30:
+Line 36:
-iface eth0 inet static
+== Wireless Bridge for GPIB instruments ==
-Line 32:
+Line 38:
-        name Marvell Technology Group Ltd. Yukon Gigabit Ethernet 10/100/1000Base-T Adapter
+On Jan 8th, 2016, a new wireless bridge (NETGEAR EX3700) for GPIB instruments was installed.
-Line 34:
+Line 40:
-        address 131.215.113.20
+Device Name: EX3700_1, Fixed IP: 192.168.113.233
-Line 36:
+Line 42:
-        netmask 255.255.255.0
+It accepts ethernet (wired) devices with fixed IP of 192.168.113.XXX
-Line 38:
+Line 44:
-        broadcast 131.215.113.255
+[[How_To_Configure_NETGEAR_EX3700]]
-Line 40:
+Line 46:
-        network 131.215.131.0
+== Nameserver and DHCP ==
`chiara` runs the DNS and DHCP for the Martian network, set up largely in the manner detailed in [[https://blogging.dragon.org.uk/dns-with-bind9-and-dhcp-on-ubuntu-14-04/|this website]].
-Line 42:
+Line 49:
-(but figure out how on a CentOS box, it'll be different).
+Configuration files can be found at{{{
chiara:/etc/bind/named.conf.local
chiara:/etc/dhcp/dhcpd.conf
}}}
-Line 44:
+Line 54:
-) Setup the name system-config-bind (needs to be done locally with GUI).  Notes:
+and other files in those same directories.
-Line 46:
+Line 56:
-- periods are important
- the forward look up (name to IP address) can list multiple names for the same IP address.  use this to give IP addresses to "services" not just specific computers.  For example, "ns.martian" is the name server, and can have the same IP address as "linux1.martian". 
- in named.conf.options be sure to enable all the interfaces that are needed, including the loop-back device (127.0.0.1)
+== Mount NFS filesystem ==
If you want to mount the `/cvs/cds` NFS filesystem on a computer already on the martian network, add the following line to the file {{{/etc/fstab}}}{{{
chiara:/home/cds              /cvs/cds        nfs     rw,bg,nfsvers=3
}}}
-Line 50:
+Line 61:
-) Add 127.0.0.1 to /etc/resolv.conf before all the other name servers, as in

nameserver 127.0.0.1

At this point you should be able to do host name look-ups:  "host linux1.martian"  If not, fix before continuing

4) replace dhcpv6_client with dhclient and add dhcp (the server package).

5) edit config file (/etc/dhcp3/dhcpd.conf on a Debian system).

6) turn off all other dhcp servers on network (linksys thing), and try rebooting something and see if it picks up an IP address and gets told the correct gateway and name server blah blah blah.

7) when you edit a config file, you'll need to restart the service.  for example, with

/etc/init.d/bind restart
+Then make the directory where the ''/cvs/cds'' dir will be mounted, mount the filesystem via {{{
mkdir -p /cvs/cds
sudo mount /cvs/cds}}}