|
Size: 4225
Comment:
|
Size: 2914
Comment:
|
| Deletions are marked like this. | Additions are marked like this. |
| Line 15: | Line 15: |
| || nameserver || 192.168.113.20 || | || nameserver || 192.168.113.104 || |
| Line 20: | Line 20: |
| . See also [[Martian_Host_Table]] for IP address assignments on the martian network. | . See the [[Martian_Host_Table|Martian host table]] for IP address assignments on the martian network. |
| Line 22: | Line 22: |
| . When you add a new host to the Martian network, choose a name from [[Computers_and_Scripts/Pool_of_Names_for_Computers]]. | . When you want to add a new host to the Martian network [[CDS/How_to_join_martian | read this]]. |
| Line 24: | Line 24: |
| . To ssh to one of the martian computers from a GC computer, ssh into {{{controls@nodus}}}, then use "name.martian" for the name. i.e. . {{{ssh pianosa.martian }}} |
. To ssh to one of the martian computers from a GC computer, ssh into `controls@nodus`, then use `name` (or `name.martian`) for the name. i.e.{{{ ssh pianosa.martian }}} |
| Line 44: | Line 44: |
| --------- | == Nameserver and DHCP == `chiara` runs the DNS and DHCP for the Martian network, set up largely in the manner detailed in [[https://blogging.dragon.org.uk/dns-with-bind9-and-dhcp-on-ubuntu-14-04/|this website]]. |
| Line 46: | Line 47: |
| Below this point the description is too old and is not valild any more (KA, Jan 8, 2016) | Configuration files can be found at{{{ chiara:/etc/bind/named.conf.local chiara:/etc/dhcp/dhcpd.conf }}} |
| Line 48: | Line 52: |
| --------- == Wireless Network == . The wireless network is part of the Martian Network. The Martian ethernet is bridged to wireless via a Linksys WRT600N wireless router with IP address https://192.168.113.220. Note that the wireless access point is only bridging the wired and wireless networks--it does not do NAT. To access the outside world, your network settings should be the same as given above for the Martian network. . You can configure the router by accessing its IP address with a web browser. . The password for configuring the wireless AP is {{{ll_admin}}}. . The manual for the router is here: [[attachment:WRT600N_Manual.pdf]] . Here are several screen shots of the configuration screens: [[attachment:screen1.pdf]] [[attachment:screen2.pdf]] [[attachment:screen3.pdf]] [[attachment:screen4.pdf]] . Here is attached the router's configuration file as of June 7, 2011. The router can reload this file if it gets lost or corrupted. [[attachment:MartianRouter.bin]] . Basically, you don't care about the internet setup because you don't connect anything to the WAN port. The physical connection to the router is just one martian LAN cable to one of the LAN ports. . Security is enforced by the MAC address filtering. Only registered machines can connect to the wireless network. Whenever you reset the router (not power cycle), you should register all the lab laptops to the router. . The SSID of the martian wireless network is {{{40MARS}}}. |
and other files in those same directories. |
| Line 72: | Line 55: |
| . If you want to mount ''linux1'' on a computer in order to share data on Martian network, add the following line on the file {{{/etc/fstab}}} . {{{ linux1:/home/cds /cvs/cds nfs rw,bg,soft 0 0 |
If you want to mount the `/cvs/cds` NFS filesystem on a computer already on the martian network, add the following line to the file {{{/etc/fstab}}}{{{ chiara:/home/cds /cvs/cds nfs rw,bg,nfsvers=3 |
| Line 76: | Line 58: |
| . Then make the directory where the ''linux1'' will be mounted on . {{{ mkdir /cvs && mkdir /cvs/cds }}} . Then reboot the computer. If it's mounted correctly you will find some directories under {{{/cvs/cds/}}} |
Then make the directory where the ''linux1'' will be mounted on{{{mkdir -p /cvs/cds}}}. Then try to mount the filesystem via {{{sudo mount /cvs/cds}}} |
The 40m has two network segments: the LIGO general computing network and an internal "martian" network.
LIGO Caltech network
IP addresses on this network are in the form 131.215.114.XXX
Martian network
IP addresses on the martian network are in the form 192.168.113.XXX
- The wireless network is on the martian network.
Gateway |
192.168.113.2 |
netmask |
255.255.255.0 |
nameserver |
192.168.113.104 |
nameserver |
131.215.125.1 |
nameserver |
131.215.139.100 |
nameserver |
131.215.254.99 |
See the Martian host table for IP address assignments on the martian network.
When you want to add a new host to the Martian network read this.
To ssh to one of the martian computers from a GC computer, ssh into controls@nodus, then use name (or name.martian) for the name. i.e.
ssh pianosa.martian
Wireless Network
On Jan 6th, 2016, the martian wifi router was replaced to Netgear R6400. Link to the corresponding ELOG entry https://nodus.ligo.caltech.edu:8081/40m/11916
This router supports 2GHz network (11g) named "40MARS" and 5GHz network (11ac) "40MARS_5G". These two SSIDs are hidden.
Wireless Bridge for GPIB instruments
On Jan 8th, 2016, a new wireless bridge (NETGEAR EX3700) for GPIB instruments is installed.
Device Name: EX3700_1, Fixed IP: 192.168.113.233
It accepts ethernet (wired) device with fixed IP of 192.168.113.XXX
How_To_Configure_NETGEAR_EX3700
Nameserver and DHCP
chiara runs the DNS and DHCP for the Martian network, set up largely in the manner detailed in this website.
Configuration files can be found at
chiara:/etc/bind/named.conf.local chiara:/etc/dhcp/dhcpd.conf
and other files in those same directories.
Mount linux1
If you want to mount the /cvs/cds NFS filesystem on a computer already on the martian network, add the following line to the file /etc/fstab
chiara:/home/cds /cvs/cds nfs rw,bg,nfsvers=3
Then make the directory where the linux1 will be mounted onmkdir -p /cvs/cds. Then try to mount the filesystem via sudo mount /cvs/cds
Firewalling by Router:WRT310N
A firewall is used for network isolation between a new CDS computer and the existing CDS system. It nicely allows to avoid a network conflict. For this purpose, a network router: LINKSYS WRT310N has been employed.
network address |
192.168.113.178 |
|
internal address |
192.168.1.1 |
|
DHCP address |
192.168.1.100-150 |
currently disabled |
Anyone can log in to the router by any web browser. The login password is set to admin.