|
Size: 1451
Comment:
|
Size: 1886
Comment:
|
| Deletions are marked like this. | Additions are marked like this. |
| Line 1: | Line 1: |
| = Vent checklists = | = Pre-vent checklists = |
| Line 4: | Line 4: |
| * Close shutter of PSL-IR and green shutters at the ends * Make shure the jam nuts are protechting bellows * Reduce input power by placing wave plate setup '''BEFORE THE PMC'''. |
|
| Line 5: | Line 8: |
| = Alignment precedure = * Align MC (center beams on MC mirrors (MCAss)) * Put input PZTs in center of range. * Place cage-mount aperture targets on BS and PRM cages * Using PZT mirrors ONLY, center beam in PRM aperture, and on PR2 folding mirror, and center PRM retro-reflection in YAW at PZT1/Faraday. * Adjust PRM pitch biases to center retro-reflection in pitch. * Add brass-mount apertures to ITMY and ETMY. * Unclamping and adjusting in yaw, adjust PR2 and PR3 folding mirrors such that beam is through BS, ITMY, and ETMY apertures. * Using PR2/3 pitch hysteresis, adjust pitch to center beam through BS/ITMY/ETMY apertures. * Adjust ITMY biases to center ITMY retro-reflection on BS. * Put apertures on ITMX and ETMX cages. * Using BS, center beam on ITMX/ETMX. NOTE: SHOULD NOT BE TOUCHING INPUT POINTING/PZTs. * Adjust ITMX biases to center ITMX retro-relfection on BS. * Should be able to see AS MICH flashes. * Adjust SR2, SR3 to center beams on SR3, SRM. * Adjust SRM for retro-reflection of AS beam at BS. |
|
| Line 8: | Line 42: |
| * Turn PZT high voltage ON * Put input PZTs in center of range. |
* Center beam on all AS optics |
| Line 11: | Line 44: |
| * Align Y arm PLUS PR2/3: * put alignment targets on ITMY/ETMY cages * use alignment ruler for PR2/3 * using PZT1/2, iteratively: * center beam on ITMY * center beam on ETMY * center beam on PR2/3 * use PR2/3 hysteresis to adjust pitch of PR2/3 * flashes in Y trans * Center beam on PRM: * height should be constrained at this point based on PR2/3 centering and Y arm alignment * move PRM cage if misaligned in yaw * PRM retro-reflection should come out REFL cleanly * Center beam on BS (should not need adjusting): * put alignment target on BS * Align X arm: * put alignment targets on ITMX/ETMX cages * use BS to center beam on ETMX * ITMX height should be constrained by BS/ETMX * adjust ITMX cage if misaligned in YAW * flashes in X trans * Align SRC * check beam centering on SR3/2/M * adjust SRM retro-reflection for centered return beam on BS * Center beam on all AS optics |
* '''GET CAMERA IMAGES OF EVERYTHING''' * We must get images right before closing, right after closing, etc. |
| Line 54: | Line 59: |
* Close PSL shutter & green shutters at the ends * Check jam nuts |
Pre-vent checklists
- Turn OFF PZT high voltage
- Close shutter of PSL-IR and green shutters at the ends
- Make shure the jam nuts are protechting bellows
Reduce input power by placing wave plate setup BEFORE THE PMC.
Alignment precedure
- Align MC (center beams on MC mirrors (MCAss))
- Put input PZTs in center of range.
- Place cage-mount aperture targets on BS and PRM cages
- Using PZT mirrors ONLY, center beam in PRM aperture, and on PR2 folding mirror, and center PRM retro-reflection in YAW at PZT1/Faraday.
- Adjust PRM pitch biases to center retro-reflection in pitch.
- Add brass-mount apertures to ITMY and ETMY.
- Unclamping and adjusting in yaw, adjust PR2 and PR3 folding mirrors such that beam is through BS, ITMY, and ETMY apertures.
- Using PR2/3 pitch hysteresis, adjust pitch to center beam through BS/ITMY/ETMY apertures.
- Adjust ITMY biases to center ITMY retro-reflection on BS.
- Put apertures on ITMX and ETMX cages.
- Using BS, center beam on ITMX/ETMX. NOTE: SHOULD NOT BE TOUCHING INPUT POINTING/PZTs.
- Adjust ITMX biases to center ITMX retro-relfection on BS.
- Should be able to see AS MICH flashes.
- Adjust SR2, SR3 to center beams on SR3, SRM.
- Adjust SRM for retro-reflection of AS beam at BS.
Closeup checklist
- Center beam on all AS optics
GET CAMERA IMAGES OF EVERYTHING
- We must get images right before closing, right after closing, etc.
- Make sure REFL is clear
- dither PRM, see motion on AP tables
- Make sure AS is clear
- dither BS/ITM, see motion on AP tables
- Using IPANG/POS pick-off mirrors, center beams on:
- IPPOS
- IPANG
Check all OpLevs centered, in and out of vacuum
- Turn PZT high voltage OFF
Close PSL shutter & green shutters at the ends
- Check jam nuts