Differences between revisions 2 and 7 (spanning 5 versions)

Vent checklists

Turn OFF PZT high voltage

Closeup checklist

Turn PZT high voltage ON
Put input PZTs in center of range.
Align Y arm PLUS PR2/3:
- put alignment targets on ITMY/ETMY cages
- use alignment ruler for PR2/3
- using PZT1/2, iteratively:
  - center beam on ITMY
  - center beam on ETMY
  - center beam on PR2/3
    - use PR2/3 hysteresis to adjust pitch of PR2/3
- flashes in Y trans
Center beam on PRM:
- height should be constrained at this point based on PR2/3 centering and Y arm alignment
- move PRM cage if misaligned in yaw
- PRM retro-reflection should come out REFL cleanly
Center beam on BS (should not need adjusting):
- put alignment target on BS
Align X arm:
- put alignment targets on ITMX/ETMX cages
- use BS to center beam on ETMX
- ITMX height should be constrained by BS/ETMX
- adjust ITMX cage if misaligned in YAW
- flashes in X trans
Align SRC
- check beam centering on SR3/2/M
- adjust SRM retro-reflection for centered return beam on BS
Center beam on all AS optics
Make sure REFL is clear
- dither PRM, see motion on AP tables
Make sure AS is clear
- dither BS/ITM, see motion on AP tables
Using IPANG/POS pick-off mirrors, center beams on:
- IPPOS
- IPANG
Check all OpLevs centered, in and out of vacuum
Turn PZT high voltage OFF

-  ⇤ ← Revision 2 as of 2012-10-22 22:23:30 → 
  Size: 151
  Editor: JamesonrollinsATligoDOTorg
  Comment:
+   ← Revision 7 as of 2012-10-23 23:54:09 → ⇥
  Size: 1463
  Editor: JennedriggersATligoDOTorg
  Comment:
-Deletions are marked like this.
+Additions are marked like this.
 Line 3:
+ * Turn OFF PZT high voltage
-Line 7:
+Line 8:
- * Put input PZTs in center of range.
 * Make sure beams are centered on
+ * --(Turn PZT high voltage ON)--
 * --(Put input PZTs in center of range.)--

 * Align Y arm PLUS PR2/3:
   * put alignment targets on ITMY/ETMY cages
   * use alignment ruler for PR2/3
   * using PZT1/2, iteratively:
     * center beam on ITMY
     * center beam on ETMY
     * center beam on PR2/3
       * use PR2/3 hysteresis to adjust pitch of PR2/3
   * flashes in Y trans

 * Center beam on PRM:
   * height should be constrained at this point based on PR2/3 centering and Y arm alignment
   * move PRM cage if misaligned in yaw
   * PRM retro-reflection should come out REFL cleanly

 * Center beam on BS (should not need adjusting):
   * put alignment target on BS

 * Align X arm:
   * put alignment targets on ITMX/ETMX cages
   * use BS to center beam on ETMX
   * ITMX height should be constrained by BS/ETMX
   * adjust ITMX cage if misaligned in YAW
   * flashes in X trans

 * Align SRC
   * check beam centering on SR3/2/M
   * adjust SRM retro-reflection for centered return beam on BS

 * Center beam on all AS optics

 * Make sure REFL is clear
   * dither PRM, see motion on AP tables
 * Make sure AS is clear
   * dither BS/ITM, see motion on AP tables

 * Using IPANG/POS pick-off mirrors, center beams on:
-Line 11:
+Line 50:
+ * Check all OpLevs centered, in and out of vacuum

 * Turn PZT high voltage OFF