Differences between revisions 2 and 10 (spanning 8 versions)

Vent checklists

Turn OFF PZT high voltage
Close shutter of PSL-IR and green shutters at the ends
Make shure the jam nuts are protechting bellows

Alignment precedure

Put input PZTs in center of range.
Place cage-mount aperture targets on BS and PRM cages
Using PZT mirrors ONLY, center beam in PRM aperture, and on PR2 folding mirror, and center PRM retro-reflection in YAW at PZT1/Faraday.
Adjust PRM pitch biases to center retro-reflection in pitch.
Add brass-mount apertures to ITMY and ETMY.
Unclamping and adjusting in yaw, adjust PR2 and PR3 folding mirrors such that beam is through BS, ITMY, and ETMY apertures.
Using PR2/3 pitch hysteresis, adjust pitch to center beam through BS/ITMY/ETMY apertures.
Adjust ITMY biases to center ITMY retro-reflection on BS.
Put apertures on ITMX and ETMX cages.
Using BS, center beam on ITMX/ETMX. NOTE: SHOULD NOT BE TOUCHING INPUT POINTING/PZTs.
Adjust ITMX biases to center ITMX retro-relfection on BS.
Should be able to see AS MICH flashes.
Adjust SR2, SR3 to center beams on SR3, SRM.
Adjust SRM for retro-reflection of AS beam at BS.

Closeup checklist

Center beam on all AS optics
Make sure REFL is clear
- dither PRM, see motion on AP tables
Make sure AS is clear
- dither BS/ITM, see motion on AP tables
Using IPANG/POS pick-off mirrors, center beams on:
- IPPOS
- IPANG
Check all OpLevs centered, in and out of vacuum
Turn PZT high voltage OFF

-  ⇤ ← Revision 2 as of 2012-10-22 22:23:30 → 
  Size: 151
  Editor: JamesonrollinsATligoDOTorg
  Comment:
+   ← Revision 10 as of 2012-12-11 00:14:03 → ⇥
  Size: 1568
  Editor: StevevassATligoDOTorg
  Comment:
-Deletions are marked like this.
+Additions are marked like this.
 Line 3:
+ * Turn OFF PZT high voltage
 * Close shutter of PSL-IR and green shutters at the ends
 * Make shure the jam nuts are protechting  bellows
-Line 4:
+Line 7:
+= Alignment precedure =

 * Put input PZTs in center of range.

 * Place cage-mount aperture targets on BS and PRM cages

 * Using PZT mirrors ONLY, center beam in PRM aperture, and on PR2 folding mirror, and center PRM retro-reflection in YAW at PZT1/Faraday.

 * Adjust PRM pitch biases to center retro-reflection in pitch.

 * Add brass-mount apertures to ITMY and ETMY.

 * Unclamping and adjusting in yaw, adjust PR2 and PR3 folding mirrors such that beam is through BS, ITMY, and ETMY apertures.

 * Using PR2/3 pitch hysteresis, adjust pitch to center beam through BS/ITMY/ETMY apertures.

 * Adjust ITMY biases to center ITMY retro-reflection on BS.

 * Put apertures on ITMX and ETMX cages.

 * Using BS, center beam on ITMX/ETMX.  NOTE:  SHOULD NOT BE TOUCHING INPUT POINTING/PZTs.

 * Adjust ITMX biases to center ITMX retro-relfection on BS.

 * Should be able to see AS MICH flashes.

 * Adjust SR2, SR3 to center beams on SR3, SRM.

 * Adjust SRM for retro-reflection of AS beam at BS.
-Line 7:
+Line 40:
- * Put input PZTs in center of range.
 * Make sure beams are centered on
+ * Center beam on all AS optics

 * Make sure REFL is clear
   * dither PRM, see motion on AP tables
 * Make sure AS is clear
   * dither BS/ITM, see motion on AP tables

 * Using IPANG/POS pick-off mirrors, center beams on:
-Line 11:
+Line 50:
+ * Check all OpLevs centered, in and out of vacuum

 * Turn PZT high voltage OFF