|
Size: 2109
Comment:
|
Size: 3491
Comment:
|
| Deletions are marked like this. | Additions are marked like this. |
| Line 12: | Line 12: |
| [[BR]] | |
| Line 13: | Line 14: |
| [[BR]] <<Anchor(plantop)>> | <<Anchor(plantop)>> |
| Line 15: | Line 16: |
| == Schnupp asymmetry measurement == | == Schnupp asymmetry measurement and its adjustment == |
| Line 17: | Line 18: |
| . {{{ Schnupp asymmetry = 0.0342 [m] +/- XXX [mm] }}} . The Schnupp asymmetry determines the reflectivity '' r ''and transmissivity '' t '' of the Michelson for the f1 and f2 sidebands when the carrier is kept in the dark condition. In the design the f2 sideband should be critical coupling for the dual recycling cavity. To achieve the critical coupling we should adjust '' r '' and '' t'' properly. . According to a simulation the asymmetry should be within the precision of XXX mm to achieve more than 95 % of the power build up. |
|
| Line 18: | Line 26: |
| . Here is an instruction how to measure the Schnupp asymmetry. | |
| Line 19: | Line 28: |
| . The result at the 40m was ... and the precision was +/- XXX mm. This implies us to fix the length of the asymmetry. |
|
| Line 21: | Line 33: |
| == PRC length measurement == | == PRC length measurement and its adjustment == |
| Line 23: | Line 36: |
| . {{{ lprc = 6.7538 [m] +/- XXX [mm] }}} . In order to resonate both f1 and f2 sidebands the length should be adjusted to .. . In addition to that the arm makes the non-zero phase shift on these sidebands and makes the .. |
|
| Line 24: | Line 43: |
| . To measure the length of the recycling cavity, |
|
| Line 25: | Line 46: |
| . | |
| Line 29: | Line 51: |
| . {{{ lsrc = 5.39915 [m] +/- XXX mm }}} |
|
| Line 30: | Line 54: |
| . | |
| Line 31: | Line 56: |
| . | |
| Line 35: | Line 61: |
| . Since the recycling gain is related to loss in the recycling cavity,... | |
| Line 36: | Line 63: |
| . | |
| Line 37: | Line 65: |
| . {{{ Carrirer = XX f1 sideband = YY f2 sideband = ZZ }}} |
|
| Line 39: | Line 72: |
| == Beam spot position on BS == === Requirements === {{{ off-centering < XXX mm }}} . To get a clean AS signal === How to === === results === |
Interferometer Characterization at the 40m prototype
Goals
To help the DRMI commissioning that will be performed at LLO.
Motivations
In the aLIGO schedule a DRMI test will start on May 2011 at LLO. Prior to the DRMI test we, the 40m lab, should help their commissioning to make the things smooth and hence allow to finish the commissioning in the shortest time. Moreover any commissioning tests that will be performed at LLO should be well predicted and tested at the 40m so that the people at the site can easily pass through all the commissioning tests and possibly can spend time for a real trouble shooting (commissioning) to fix unexpected issues.
- So for this purpose some recipes must be prepared by the 40m lab. Each recipe includes descriptions about how to make a commissioning test, how to estimate important parameters and the results at the 40m. Additionally some useful scripts must be developed at the 40m.
Contents
- Interferometer Characterization at the 40m prototype
-
DRMI Characterization Plan at the 40m
- Schnupp asymmetry measurement and its adjustment
- PRC length measurement and its adjustment
- SRC length measurement
- Recycling gain measurements
- Beam spot position on BS
- Reflectivity check
- Sensing matrix check
- Calibration of Actuator responses
- f2a filter adjustment
- IFO modeling
- Estimation of Suspensions' Position
- Locking procedure
- MICH actuator decoupling
DRMI Characterization Plan at the 40m
Schnupp asymmetry measurement and its adjustment
Requirement
Schnupp asymmetry = 0.0342 [m] +/- XXX [mm]
The Schnupp asymmetry determines the reflectivity r and transmissivity t of the Michelson for the f1 and f2 sidebands when the carrier is kept in the dark condition. In the design the f2 sideband should be critical coupling for the dual recycling cavity. To achieve the critical coupling we should adjust r and t properly.
- According to a simulation the asymmetry should be within the precision of XXX mm to achieve more than 95 % of the power build up.
How to
- Here is an instruction how to measure the Schnupp asymmetry.
Results
- The result at the 40m was ... and the precision was +/- XXX mm. This implies us to fix the length of the asymmetry.
PRC length measurement and its adjustment
Requirements
- {{{ lprc = 6.7538 [m] +/- XXX [mm]
}}}
- In order to resonate both f1 and f2 sidebands the length should be adjusted to ..
- In addition to that the arm makes the non-zero phase shift on these sidebands and makes the ..
How to
- To measure the length of the recycling cavity,
Results
SRC length measurement
Requirements
- {{{ lsrc = 5.39915 [m] +/- XXX mm }}}
How to
Results
Recycling gain measurements
- Since the recycling gain is related to loss in the recycling cavity,...
How to
Results
Carrirer = XX f1 sideband = YY f2 sideband = ZZ
Beam spot position on BS
Requirements
{{{ off-centering < XXX mm }}}
- To get a clean AS signal
How to
results
Reflectivity check
How to
Results
Sensing matrix check
How to
Results
Calibration of Actuator responses
How to
Results
f2a filter adjustment
Requirement
How to
Results
IFO modeling
How to
Results
Estimation of Suspensions' Position
Requirements
How to
Results
Locking procedure
How to
MICH actuator decoupling
Requirements
How to
[#plantop back to top]