Diff for "Electronics/VideoMUX"

Differences between revisions 2 and 12 (spanning 10 versions)

Overview

Our new Video Switch is a [http://www.extron.com/product/product.aspx?id=mavplus3232v Extron MAV PLUS 3232].

attachment:mavpic.jpg

Setup Howto

Connect ethernet cable directly to the videos switcher with a computer.
from the computer, go to default switcher's address 192.168.254.254 by using web browser like firefox.
if you can not see any pages in the browser, try telnet to 192.168.254.254 to check the connection.
change the IP address, the Gateway address and subnet mask properly in the web page.
put the video switcher into the network via another ethernet cable.
you can access the switcher from anywhere in the 40m by using web browser
connect analog video cables
assign output-input matrix by accessing the switcher from an web browser

Docs

attachment:manuel.pdf

attachment:quickref.pdf

Configuration

network

name = LUCIANA
address = http://131.215.113.92/

channel assign

more information about output channels and monitors are below.

channel assign
INPUT
channel	camera	state
1	MC2
2	Faraday
3	PSL output CAM	-
4	BS
5	MC13	camera disconnected
6	ITMX
7	ITMY
8	ETMX
9	ETMY
10	-	-
11	RCR
12	RCT
13	OMCR	-
14	PMCR
15	PSL IOO	-
16	IMCT	not aligned ?
17	PSL	-
18	IMCR	-
19	SPS
20	POB	-
21	POX	no camera
22	APS1
23	ETMXT	not aligned
24	ETMYT	no camera
25	POY	no camera
26	OMCT

-  ⇤ ← Revision 2 as of 2009-12-29 08:14:09 → 
  Size: 253
  Editor: RanaAdhikari
  Comment:
+   ← Revision 12 as of 2009-12-30 09:23:23 → ⇥
  Size: 2255
  Editor: KiwamuIzumi
  Comment:
-Deletions are marked like this.
+Additions are marked like this.
 Line 7:
-.
 1.
 1.
+. Connect ethernet cable directly to the videos switcher with a computer.
 1. from the computer, go to default switcher's address 192.168.254.254 by using web browser like firefox.
 1. if you can not see any pages in the browser, try telnet to 192.168.254.254 to check the connection.
 1. change the IP address, the Gateway address and subnet mask properly in the web page.
 1. put the video switcher into the network via another ethernet cable.
 1. you can access the switcher from anywhere in the 40m by using web browser
 1. connect analog video cables
 1. assign output-input matrix by accessing the switcher from an web browser
-Line 16:
+Line 20:
+== Configuration ==
=== network ===
 * name = '''LUCIANA'''
 * address = http://131.215.113.92/

=== channel assign ===
 . more information about output channels and monitors are below.

 ||||||||<#FF8080>''' channel assign'''||
 ||||||<#80FF80>  '''INPUT'''||
 || ''channel'' || ''camera'' || ''state'' ||
 || 1     ||   MC2    ||  :)     ||
 || 2     ||  Faraday ||  :)     ||
 || 3     ||  PSL output CAM||  -    ||
 || 4     ||   BS     ||  :)     ||
 || 5     ||    MC13  ||  camera disconnected    ||
 || 6     ||   ITMX   ||  :)     ||
 || 7     ||   ITMY   ||  :)     ||
 || 8     ||   ETMX   ||  :)     ||
 || 9     ||   ETMY   ||  :)     ||
 || 10    ||     -    ||  -   ||
 || 11    ||   RCR    ||  :)    ||
 || 12    ||   RCT    ||  :)    ||
 || 13    ||   OMCR   ||  -   ||
 || 14    ||   PMCR   ||  :)    ||
 || 15    ||  PSL IOO ||  -    ||
 || 16    ||   IMCT   ||  not aligned ?    ||
 || 17    ||    PSL   ||  -    ||
 || 18    ||   IMCR   ||  -    ||
 || 19    ||   SPS    ||  :)    ||
 || 20    ||   POB    ||  -    ||
 || 21    ||   POX    ||  no camera    ||
 || 22    ||   APS1   ||  :)    ||
 || 23    ||   ETMXT  ||  not aligned    ||
 || 24    ||   ETMYT  ||  no camera      ||
 || 25    ||    POY   ||  no camera      ||
 || 26    ||    OMCT  ||   :)     ||

=== monitors and output channels ===
     <<ImageLink(monitos.png, monitors and channels, height=150)>>