RF Frequency Distribution box

The box is going to be installed in the LSC rack. It will get the demodulation signals from the frequency generation box and it will split it into several output so that it can be used by the demodulation boards.
The box is also going to generate frequency multiples as 3xf1, 3xf2, 2xf1 and 2xf2 demod signals.

Pictures

This is how the Frequency Distribution Box is going to look like.

Plans

RF Distribution
- 1. Construction of Frequency Distribution Box
- exactly the same as for the frequency generation box
- 1. Demod board filter upgrade: installation of surface mount low pass/high pass filter
- 1. LSC rack routing

Early Thoughts

40m Upgrade RF Distribution Box

This box will serve to split the RF signal coming from the RF Modulation Generator into the signals to be fed to the demod boards.
It will distribute both 11 and 55 MHz frequencies. It will also provide the 3f demod signals.
The box will contain 2 8-way power splitters, 2 frequency triplers, 2 2-way power splitters.
The box will have to be powered.

Electronics/RF_System/frequency_distribution_box (last edited 2012-01-03 23:02:38 by localhost)

-  ⇤ ← Revision 8 as of 2011-11-01 00:29:29 → 
  Size: 1424
  Editor: KiwamuIzumi
  Comment: The naming convention was obsolte
+   ← Revision 11 as of 2011-11-05 01:26:16 → ⇥
  Size: 1446
  Editor: KiwamuIzumi
  Comment:
-Deletions are marked like this.
+Additions are marked like this.
 Line 2:
-This page describes the 40m Upgrade '''Frequency Distribution Box'''.

The box is going to be installed in the LSC rack. It will get the demodulation signals from the [[/frequency generation box|frequency generation box]] and it will split it into several output so that it can be used by the demodulation boards.

The box is also going to generate frequency multiples as 3xf1, 3xf2, 2xf1 and 2xf2 demod signals.
-Line 10:
+Line 5:
-== Pictures ==
+= RF Frequency Distribution box =
 . The box is going to be installed in the LSC rack. It will get the demodulation signals from the [[Electronics/RF system/frequency generation box|frequency generation box]] and it will split it into several output so that it can be used by the demodulation boards.
-Line 12:
+Line 8:
-This is how the Frequency Distribution Box is going to look like.
+ . The box is also going to generate frequency multiples as 3xf1, 3xf2, 2xf1 and 2xf2 demod signals.


= Pictures =

 . This is how the Frequency Distribution Box is going to look like.
-Line 16:
+Line 17:
-== Plans ==
+= Plans =
-Line 18:
+Line 19:
-'''RF Distribution'''
  1. Construction of Frequency Distribution Box
+ . '''RF Distribution'''
   . 1. Construction of Frequency Distribution Box
-Line 21:
+Line 22:
-. Demod board filter upgrade: installation of surface mount low pass/high pass filter
  1. LSC rack routing
+   . 1. Demod board filter upgrade: installation of surface mount low pass/high pass filter
   . 1. LSC rack routing
[[BR]]
-Line 26:
+Line 28:
-This box will serve to split the RF signal coming from the [[Upgrade 09/RF System/RF_Modulation_Generator|RF Modulation Generator]] into the signals to be fed to the demod boards.
+ . This box will serve to split the RF signal coming from the [[Upgrade 09/RF System/RF_Modulation_Generator|RF Modulation Generator]] into the signals to be fed to the demod boards.
-Line 28:
+Line 30:
-It will distribute both 11 and 55 MHz frequencies. It will also provide the 3f demod signals.
+ . It will distribute both 11 and 55 MHz frequencies. It will also provide the 3f demod signals.
-Line 30:
+Line 32:
-The box will contain 2 8-way power splitters, 2 frequency triplers, 2 2-way power splitters.
+ . The box will contain 2 8-way power splitters, 2 frequency triplers, 2 2-way power splitters.
-Line 32:
+Line 34:
-The box will have to be powered.
+ . The box will have to be powered.